Hikvision Cat 6 UTP Cable — 305m Reel
The Hikvision Cat 6 UTP cable is a structured cabling solution engineered for Gigabit Ethernet networks and IP-based security infrastructure. It meets the ANSI/TIA-568.2-D and ISO/IEC 11801 Cat 6 (Class E) performance standards, supporting 250 MHz bandwidth across the full 100-metre horizontal channel. Furthermore, Hikvision’s positioning as a vertically integrated security and networking manufacturer makes this cable a natural fit for installations where IP cameras, NVRs, and access control systems share the same structured cabling plant as general data network infrastructure.
Supplied on a 305-metre (1,000 ft) pull-box reel, the Hikvision Cat 6 cable is suited to both dedicated IP surveillance cabling runs and general-purpose horizontal LAN installations in commercial and light-industrial environments.
Performance and Bandwidth
The Hikvision Cat 6 cable operates at a rated bandwidth of 250 MHz. This exceeds the 100 MHz floor of Cat 5e and supports Gigabit Ethernet (1000BASE-T) across the full 100-metre channel. Additionally, it accommodates 10GBASE-T over shorter horizontal runs of approximately 55 metres or less within a standard channel, providing a degree of forward compatibility with 10G switching infrastructure.
Key electrical performance parameters — including near-end crosstalk (NEXT), power sum NEXT (PS-NEXT), and attenuation-to-crosstalk ratio (ACR) — are controlled to Cat 6 standard limits. In IP surveillance deployments specifically, these parameters support stable, uninterrupted video transmission over long horizontal runs from camera locations to patch panels and NVR equipment.
Cable Construction
The Hikvision Cat 6 cable uses four twisted pairs of 23 AWG bare copper conductors. An internal spline separator physically isolates each pair within the jacket, reducing internal crosstalk between pairs and limiting signal interference in high-density bundle environments. The tighter twist rates per pair compared to Cat 5e further improve noise rejection — relevant in environments where power cabling and data cabling share the same cable tray or conduit pathway.
The PVC jacket carries a CMR (Communications Multipurpose Cable, Riser) rating, making it suitable for installation in vertical riser pathways between floors. LSZH jacket variants are available for environments governed by fire safety regulations covering smoke toxicity and flame spread, including transport infrastructure, healthcare buildings, and public assembly spaces.
IP Surveillance Suitability
The Hikvision Cat 6 cable is specifically well-matched to IP camera infrastructure. Modern Hikvision IP cameras — including 4MP, 8MP, and multi-sensor models — generate continuous high-bitrate video streams that demand consistent signal integrity across the full horizontal run. Cat 6’s controlled attenuation and crosstalk parameters support these streams reliably at distances up to 100 metres.
Beyond data transmission, PoE and PoE+ power delivery (IEEE 802.3af and 802.3at) over the same cable eliminates the need for separate mains power runs to each camera location. For higher-power devices including IR illuminators, PTZ cameras, and multi-sensor units, PoE++ (IEEE 802.3bt, up to 90W) is supported within a compliant Cat 6 channel — reducing installation cost and infrastructure complexity on security projects.
Extended PoE (ePoE) distance modes, available on select Hikvision NVRs and switches, can extend powered transmission beyond the standard 100-metre limit on dedicated point-to-point runs. Cable quality directly affects the maximum achievable ePoE distance, making a consistent, standards-compliant cable like the Hikvision Cat 6 preferable to unbranded or substandard alternatives on long camera runs.
Installation Characteristics
The Hikvision Cat 6 cable is supplied on a 305-metre pull-box reel, the standard format for horizontal cabling projects. The pull-box facilitates controlled payout during installation across ceiling voids, cable trays, conduit systems, and wall cavities.
The cable maintains a maximum pulling tension of 110N and a minimum bend radius of 25mm during installation. Adhering to these parameters is essential on long surveillance cable runs — damage from over-tensioning or tight bends can introduce signal degradation that is difficult to locate and diagnose after installation is complete.
The cable terminates into standard Cat 6 keystone jacks, patch panels, and RJ45 field-termination plugs. On Hikvision-centric installations, pairing the cable with Hikvision’s own patch panels and keystone hardware supports a single-vendor infrastructure approach that simplifies procurement, support, and system warranty management.
Standards and Certifications
The Hikvision Cat 6 cable is manufactured to the following standards:
- ANSI/TIA-568.2-D — North American structured cabling standard for Cat 6 balanced twisted-pair cabling
- ISO/IEC 11801 — International performance specification for Class E horizontal cabling
- IEEE 802.3ab — 1000BASE-T Gigabit Ethernet over twisted-pair copper
- IEEE 802.3bt — PoE++ up to 90W
- IEC 60332 — Flame retardancy (LSZH variants)
- RoHS Compliant — Restriction of Hazardous Substances directive compliance
Supported Applications
The Hikvision Cat 6 cable supports the following applications within a 100-metre horizontal channel:
- 1000BASE-T — Gigabit Ethernet (IEEE 802.3ab)
- 100BASE-TX — Fast Ethernet
- 10GBASE-T — 10 Gigabit Ethernet over shorter runs (~55m channel)
- PoE / PoE+ — Up to 30W per port (IEEE 802.3af / 802.3at)
- PoE++ — Up to 90W per port (IEEE 802.3bt Type 3/4)
- Hikvision ePoE — Extended powered transmission on point-to-point runs (NVR/switch dependent)
- IP Surveillance — 4K/8MP camera video and power over structured cabling
- Access Control and Intercoms — PoE-powered door controllers, readers, and video intercoms
- VoIP — IP telephony over converged network infrastructure
- Wi-Fi Access Points — PoE-powered 802.11ac/ax WAP backhaul
Ideal Users
- Security Systems Integrators and CCTV Installers — The Hikvision Cat 6 cable is a direct fit for Hikvision IP camera deployments. It supports the full PoE++ power budget required by high-end PTZ and multi-sensor cameras, and its Cat 6 signal integrity parameters handle the continuous high-bitrate streams of 4K and 8MP cameras across 100-metre runs. Using Hikvision cable on Hikvision camera projects simplifies single-vendor procurement and support.
- Commercial Property Fit-Out Contractors — Cat 6 at 250 MHz delivers a structured cabling foundation that supports both the IP security overlay and the general data network within the same horizontal cabling plant. The 305m reel format suits the volume cabling requirements of multi-floor commercial fit-outs.
- IT Infrastructure Managers in SME and Mid-Market Organisations — Where network refresh budgets need to accommodate both LAN upgrades and IP surveillance expansion simultaneously, a shared Cat 6 structured cabling plant reduces total infrastructure cost. PoE++ support means camera and wireless access point power is delivered over existing data cabling without separate electrical circuits.
- Facilities Managers in Education and Healthcare — PoE-powered IP cameras, access control readers, nurse call systems, and Wi-Fi access points can all be connected over a single Hikvision Cat 6 cabling infrastructure. The LSZH jacket variant satisfies fire safety specifications common in school and hospital building regulations.
- System Integrators on Unified Security and Network Projects — In projects where Hikvision NVRs, PoE switches, access control panels, and IP intercoms are all part of the same bill of materials, specifying Hikvision Cat 6 cable unifies the cabling layer under the same vendor ecosystem — streamlining procurement, installation sign-off, and ongoing support.
Cable Specifications
| Attribute | Detail |
|---|---|
| Category | Cat 6 (Class E) |
| Standard | ANSI/TIA-568.2-D / ISO/IEC 11801 |
| Conductor | 23 AWG Bare Copper |
| Pairs | 4 Twisted Pairs |
| Shield Type | Unshielded (U/UTP) |
| Pair Separator | Internal Spline (cross-filler) |
Performance Specifications
| Attribute | Detail |
|---|---|
| Rated Bandwidth | 250 MHz |
| Max Channel Length | 100 metres |
| 10GBASE-T Support | Up to ~55m (standard channel) |
| Impedance | 100Ω (±15Ω) |
| NEXT (at 100 MHz) | ≥44.3 dB |
| PS-NEXT (at 100 MHz) | ≥42.3 dB |
| Attenuation (at 100 MHz) | ≤19.8 dB/100m |
Physical Specifications
| Attribute | Detail |
|---|---|
| Jacket Material | PVC (CMR Riser) / LSZH (optional) |
| Outer Diameter | Approx. 6.0mm |
| Reel Length | 305m (1,000 ft) |
| Packaging | Pull-box reel |
| Colour Options | Grey, Blue, White (varies by SKU) |
| Operating Temperature | -20°C to +60°C |
| Installation Temperature | 0°C to +50°C |
Installation Parameters
| Attribute | Detail |
|---|---|
| Maximum Pull Tension | 110N |
| Minimum Bend Radius (installation) | 25mm |
| Minimum Bend Radius (installed) | 25mm |
| Recommended Termination | Cat 6 Keystone Jacks / RJ45 Field Plugs |
PoE Support
| Standard | Power Delivery |
|---|---|
| IEEE 802.3af (PoE) | Up to 15.4W per port |
| IEEE 802.3at (PoE+) | Up to 30W per port |
| IEEE 802.3bt (PoE++) | Up to 90W per port |
| Hikvision ePoE | Extended range (NVR/switch dependent) |
Certifications
| Certification | Detail |
|---|---|
| TIA | ANSI/TIA-568.2-D Cat 6 |
| ISO/IEC | 11801 Class E |
| IEEE | 802.3ab (1000BASE-T), 802.3bt (PoE++) |
| Flame | IEC 60332 (LSZH variant) |
| Environmental | RoHS Compliant |
No products in the cart. 
Reviews
There are no reviews yet.